These are the settings of an Efficient Networks 5861 ADSL router, connected to the internet via the UK ADSL system provided by BT. They are not necessarily the best or even correct settings but if your 5861 has these settings you should be able to browse to 1 single web page, at http://www.bt.net/digitaldemo. If you can't get to that page with these settings then you need to talk to your ISP. |
|
GENERAL INFORMATION FOR <user@server.net-router> |
|
System started on | 3/22/2002 at 10:16 |
Authentication override | none |
WAN to WAN Forwarding | yes |
Block NetBIOS Default | no |
BOOTP/DHCP Server address | none |
Telnet Port | default (23) |
Telnet Clients | LAN |
SNMP Port | default (161) |
SNMP Clients | LAN |
HTTP Port | default (80) |
HTTP Clients | LAN |
Syslog Port | default (514) |
Allowed Syslog Servers | LAN |
Default Syslog Servers | none |
System message: Configured_by_Internet_Quick_Start | |
Security timer | 10 minutes |
One WAN Dial Up | no |
Backup | no (no valid remote profile is enabled) |
Retry Interval In Minutes | 30 |
Stability Interval In Minutes | 3 |
MODEM STRINGS: Reset: ATZ Escape: +++ Init: ATS0=0Q0V1&C1&D0X4S12=20 Off-Hook: ATH1 Dial: ATDT Answer: ATA Hangup: ATH0 GLOBAL BRIDGING/ROUTING SETTINGS: |
|
Bridging enabled | no |
Exchange spanning tree with dest | yes |
Bridge only PPPoE with dest | no |
IP Routing enabled | yes |
Multicast forwarding enabled | no |
Firewall filter enabled | yes |
Directed Broadcasts Allowed | no |
RIP Multicast address | default |
VRRP Multicast address | default |
IPX Routing enabled | no |
ETHERNET INFORMATION FOR <ETHERNET/0> | |
Hardware MAC address | nn:nn:nn:nn:nn:nn |
Send IP RIP to the LAN | rip-1 compatible |
Advertise me as default router | yes |
Process IP RIP packets received | rip-1 compatible |
Receive default route by RIP | yes |
IP address translation | no |
IP filters defined | no |
IP address/subnet mask | 192.168.254.254/255.255.255.0 |
Management IP address/subnet mask | 0.0.0.0/0.0.0.0 |
Static Ethernet routes defined | none |
Virtual Ethernet routes defined | none |
IPX External network number | 00000000 |
IPX Frame type | 802.2 |
MTU | default |
INFORMATION FOR <internet> |
|
Status | enabled |
Our System Name when dialing out | bt_test@startup_domain |
Our Password used when dialing out | yes |
Interface in use | HSD |
Protocol in use | PPP |
ATM traffic shaping | no |
Authentication | disabled |
Authentication level required | PAP |
Use periodic LCP pings | yes |
Connection Identifier (VPI*VCI) | 0*38 |
IP address translation | on |
IP filters defined | no |
Send/Receive Multicast | off |
Block NetBIOS Packets | on |
Compression negotiation | off |
IP slave mode (PPP) | no |
Try to reacquire IP addr (PPP) | yes |
Accept LAN configuration | no |
Retry Timer (PPP) | 0 |
Source IP address/subnet mask | 0.0.0.0/0.0.0.0 |
Remote IP address/subnet mask | 0.0.0.0/0.0.0.0 |
Management IP address/subnet mask | 0.0.0.0/0.0.0.0 |
Send IP RIP to this dest | no |
Send IP default route if known | no |
Receive IP RIP from this dest | no |
Receive IP default route by RIP | no |
Keep this IP destination private | yes |
Total IP remote routes | 1 |
0.0.0.0/0.0.0.0/1 | |
IPX network number | 00000000 |
Use IPX RIP/SAP (negotiate with PPP): | yes |
Total IPX remote routes | 0 |
Total IPX SAPs | 0 |
Bridging enabled | no |
Exchange spanning tree with dest | no |
Bridge only PPPoE with dest | no |
mtu | 1500 |
Main Site | Software | Contact Us |